evo-sanwa-fh4
-17%
MXO Racing

MINI-Z EVO SANWA FH4 Receiver Conversion 4CH Receiver Module [MXO RACING] EVO-RX-SANWA-FH4

$59.99
$49.99 In Stock Pre-Order Sold out
SKU: EVO-RX-SANWA-FH4
Notify when available

1-4 DAYS DELIVERY

100% ORIGINAL AND QUALITY

24 MONTHS GUARANTEE

  • Description
  • Reviews

MINI-Z EVO SANWA FH4 Receiver Conversion 4CH Receiver Module [MXO RACING] EVO-RX-SANWA-FH4
This MINI receiver module is for you to connect your EVO board to a SANWA Radio system that uses FH4 Communication.


This is the receiver for KYOSHO MR-03EVO and MA-030EVO
it can be used for sanwa transmitter
M12S,M12,MT44,MT4S,MT4,M11X etc.
*PLEASE CHECK WHAT PROTOCOLS YOUR TRANSMITTER CAN HANDLE!
MX EVO RX-SANWA V2 . 15 Manual
The MX EVO RX -SANWA is a SANWA FH3/FH4 compatible ultra - miniature receiver for KYOSHO's MR -03EVO and MA -030EVO , with an output speed of up to 2 . 6ms in EVO mode . It can work not only in EVO mode , but also in 4CH PWM standard signal mode .
Features:
Size: 10.5*10.0*3.5mm;
Weight: 0.72g;
Working voltage: 3.0V or 3.3V;
Compatible with SANWA FH3/FH4 protocol;
Support EVO and 4CH PWM two working modes;
The output speed in EVO mode is 2.6ms;
The output speed in 4CH PWM mode is 5 .4ms;


Bind Operation:
Install the MX EVO RX first , then power on the receiver and press the BIND switch until the red LED on the RX changes from slow flashing to fast flashing .
Power on the transmitter , then set it to SFHSS mode (if it is already in SFHSS mode , ignore this step) , wait for a few seconds , when the LED on the receiver changes from fast flashing to steady light , it means BIND is successful and the receiver is already in normal mode .
Red LED status indication:
The red LED on the MX EVO RX is an indication of the working status of the RX:
1) When the red LED flashes slowly , it means that RX is waiting to receive a signal;
2) When the red LED flashes quickly , it means RX is in BIND mode;
3) When the red LED is always on , it means that the RX has received the signal stably .
Green LED status indication:
The green LED on the MX EVO RX is an indication of the RX operating mode:
1) When the green LED is on , it means the RX is working in EVO mode;
2) When the green LED is off , it means that the RX is working in 4CH PWM mode;
How to set up the transmitter (when MX EVO RX is used on MR -03EVO/MA -03EVO):
Because the brushless ESCs and servos on MR -03EVO/MA -03EVO cannot set the midpoint and end point , the user can only set the transmitter to adapt to the parameters of MR -03EVO/MA -03EVO . The settings are as follows:
1)TH TYPE    >   F5 : B5
2)EAP: ST >L150% R150%
TH >H150% B150%
3)D/R:  ST >100%
TH >100%
4)REV: ST >REV
TH >REV
Note: Points 2 and 3 can be adjusted according to user habits .
How the MX EVO RX works in EVO mode:
When users install MX EVO RX on KYOSHO's MR -03EVO/MA -03EVO frame or other products that support EVO mode , MX EVO RX will work in EVO mode .
In EVO mode , when the MX EVO RX is just powered on , the LED on the RX will not flash quickly , but the green LED will light up .
Note: When using the MX EVO RX on the MR -03EVO/MA -03EVO , be sure to install it in place , otherwise you may burn it; if necessary , place the receiver compartment cover on the MR -03EVO/ MA -03EVO Add a small piece of sponge to hold down the MX EVO RX .
How the MX EVO RX works in 4CH PWM mode:
When users install MX EVO RX on EVO - BA1 or other products that support 4CH PWM mode , MX EVO RX will work in 4CH PWM mode .
In 4CH PWM mode , when the MX EVO RX is just powered on , the LED on the RX will flash several times quickly and then enter the working mode , but the green LED will be off .
The picture below shows the EVO - BA1 on the left and the EVO - BA1 with the MX EVO RX installed on the right:

Customer Reviews

Based on 1 review
100%
(1)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
R
R.H.
Perfect fit.

This is the exact reciever you'll need if you're running an mr04 evo2 with an m17 or the older fh4 remotes(mt44 etc.) Fits great. Need to put foam between reciever cover and reciever to make sure it doesn't wiggle out... otherwise perfect.

Recently Viewed